Bed Claw Unibody Adjustable Height Bed F... from $23.00
The Benefits of a Center Support System | All beds, especially those Queen Size and larger, will benefit from the center support. A Center Support supports your foundation unit and mattress in the middle, thus reducing stress on those units. Most mattress manufacturers require center support for their warranty to be valid. Wood Bed Slats Need Center Support Also | Many beds still use the wood slat method for supporting the mattress/foundation unit. Beds utilizing wood slats for support need added legs in the middle to prevent bowing and cracking of the slats because wood naturally changes over time. The NEW Bed Claw Unibody Adjustable Height Bed Slat Support Leg | The Bed Claw new leg features strong, one-piece unibody construction. No rivets are employed; it is made from a single piece of steel that has been formed and welded. It will protect both carpet and hard floors. We are constantly working to improve our products and bring even better value to our customers. How Many Should I Install? You may install as few or as many as you prefer. Most customers choose to use 2 or 3 support legs, each installed in the center of a wood slat along the length of the bed. Height Adjustable from 6-1/2" and 10" or between 11-1/2" and 14-3/4" with the included extender. No extra trips to the Hardware Store. Your package comes complete with all you need to properly install your Unibody. (Should your height be between 10" and 11-1/2", you should purchase our SLATJACK, which includes additional glides to allow you access to this height range.) Included Hardware with Each Leg - Wing Nut - Jam Nut (the little one) - Coupler Nut (the big one) - #8-3/4" Phillips Wood Screw (4) Ltd. Lifetime Service Policy Our Ltd. Lifetime Policy runs from the original date of purchase and covers the repair of manufacturing defects or replacement of your purchased product. Item must be clean and free of stains or damage. Transportation charges and a Policy Service Fee are the responsibility of the consumer. To email, your clear images of the issue go to the storefront for our contact information. Then you will receive information on the next steps and/or additional information on this policy.
Bed Claw SlatJack Adjustable Center Supp... from $38.00 $49.88
The SlatJack adjustable center support leg is designed for bed slats or furniture that needs extra strength to fix, prevent, or underpin sagging issues. Developed and designed by BED CLAW, the SlatJack acts as a jack for your bed or furniture to prevent or correct sagging. Used with wood slats on your bed, the SlatJack adds years of comfortable sleep and is the #1 solution for sagging mattresses. Using one Slat Jack in the middle of each wood bed slat is sufficient to eliminate the all to infrequent, albeit distracting, creaking sounds while providing ample mattress frame support.Each SlatJack leg comes with 2 adjustable height glides. One is 2.5" tall while the other is 5" tall. These, especially when combined with the included adjustable extenders, provide you the ability to tailor the SlatJack to a wider range of heights when compared to other less useful support legs. If your bed is anywhere from roughly 6" to 15" off the floor the SlatJack will help provide a stable base for your bed slats to help prevent sagging.Top Mounting Plate Dimensions: 3" x 1 15/16"The large smooth plastic glide is 1 7/8" wide for excellent weight distribution. The large size helps prevent carpet and hard floor damage.Height Adjustable from 6-1/2" to 14-3/4".If your bed is between 10" to 11-1/2" tall from the floor to where the box spring rests, you'll want to utilize a combination of the extender and the shorter 2-1/2" glide included to gain access to this height range. All needed hardware, including screws, included
Bed Claw No Sag Mattress Slats - Center ... $136.00 $149.99
Special Note | Please review the item description and detailed measurements that are provided to ensure this product will work for your application, as center supports are non-returnable. New Adjustable Bed Rail Center Support System | Due to increasing demand for a strong center support system capable of attachment to lower height beds, the Hospitality No-Sag Center Mattress Support has been developed. It consists of 3 Steel Cross Rails, each with one adjustable Glide equipped leg. Adjustable | The Hospitality No-Sag Center Mattress Support is easily adjustable in width and height. It will adjust in Width from 52" up to 77" to fit the following bed sizes: Full, Queen, California King, and King Size. It will adjust in height from a minimum of 4" up to a maximum of 15". Weight Capacity | The Hospitality No-Sag Center Mattress Support passed the Static Load Testing of 2,000 pounds. The glide on the bottom of each of the three adjustable legs is 2" in diameter, assuring good weight distribution while protecting floors and carpeting. Rail Attachment | This center support system may be attached to either wooden bed side rails or metal bed frame rails. Depending on the metal rails to which attachment is to be made, some drilling may be necessary for the attachment. Some Assembly Required | Some assembly is required. Illustrated Assembly Instructions are included as are tools required for assembly. Specifications Fits These Bed Sizes: Full, Queen, California King, and King Size Adjustable Height: 4" to 15" Weight Capacity: 2,000 pounds Number of Adjustable Cross Arms: 3 Number of Adjustable Glide Equipped Legs: 3 (one on each cross arm)
Bed Claw LOW PROFILE No-Sag Center Suppo... $119.00 $179.99
Due to the increasing demand for a strong center support system capable of attachment to lower height beds, the Bed Claw LOW PROFILE No-Sag Center Support System has been developed. It consists of 3 Steel Cross Rails, each with one adjustable leg. Designed to reinforce your bed's central area, which bears about 70% of your weight. Strategically placed support helps prevent warping, broken wooden slats, and damaged side rails cleats (or lips) that hold your bedding. Included wood screws to attach this support to your wooden side rail cleats. Though designed primarily for use with wooden side rails, this support can be used on beds with metal side rails. When used with metal side rails, it is likely that you will need to have the capability of drilling holes into your metal side rails for securing the supports into place. You'll need a power drill and a drill bit that is designed for drilling into metal. The Bed Claw LOW PROFILE No-Sag Center Support System is easily adjustable in width and height. It will adjust in Width from 52" up to 77" to fit the following bed sizes: Full, Queen, King, and California King Size. It will adjust in height from a minimum of 4" up to a maximum of 9.5". We kindly ask you to measure before ordering. The Bed Claw LOW PROFILE No-Sag Center Support System passed the Static Load Testing of 2,000 pounds. The glides on the bottom of each of the three adjustable legs are 2" in diameter, assuring good weight distribution while protecting floors and carpeting. Some assembly is required. Instructions are included as are tools required for assembly. Please contact us should you have any additional questions or concerns regarding this item, we are happy to assist. Specifications: Fits These Bed Sizes: Full, Queen, King, and California King Adjustable Height: 4" to 9.5" Weight Capacity: 2,000 pounds Adjustable Cross Arms: 3 Adjustable Glide Equipped Legs: 3 (one per cross arm)